To boot S-mode firmware payload like EDK2 from persistent
flash storage, qemu needs to pass the flash address as the
next_addr in fw_dynamic_info to the opensbi.
When both -kernel and -pflash options are provided in command line,
the kernel (and initrd if -initrd) will be copied to fw_cfg table.
The S-mode FW will load the kernel/initrd from fw_cfg table.
If only pflash is given but not -kernel, then it is the job of
of the S-mode firmware to locate and load the kernel.
In either case, update the kernel_entry with the flash address
so that the opensbi can jump to the entry point of the S-mode
firmware.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221004092351.18209-4-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFiveEState inherits from SysBusDevice while it's TypeInfo claims it to
inherit from TYPE_MACHINE. This is an inconsistency which can cause
undefined behavior such as memory corruption.
Change SiFiveEState to inherit from MachineState since it is registered
as a machine.
Fixes: 0869490b1c ("riscv: sifive_e: Manually define the machine")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220922075232.33653-1-shentey@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the OpenTitan hardware the resetvec is fixed at the start of ROM. In
QEMU we don't run the ROM code and instead just jump to the next stage.
This means we need to be a little more flexible about what the resetvec
is.
This patch allows us to set the resetvec from the command line with
something like this:
-global driver=riscv.lowrisc.ibex.soc,property=resetvec,value=0x20000400
This way as the next stage changes we can update the resetvec.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220914101108.82571-4-alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Booting using "Direct Kernel Boot" for PolarFire SoC & skipping u-boot
entirely is probably not advisable, but it does at least show signs of
life. Recent Linux kernel versions make use of peripherals that are
missing definitions in QEMU and lead to kernel panics. These issues
almost certain rear their head for other methods of booting, but I was
unable to figure out a suitable HSS version that is recent enough to
support these peripherals & works with QEMU.
With these peripherals added, booting a kernel with the following hangs
hangs waiting for the system controller's hwrng, but the kernel no
longer panics. With the Linux driver for hwrng disabled, it boots to
console.
qemu-system-riscv64 -M microchip-icicle-kit \
-m 2G -smp 5 \
-kernel $(vmlinux_bin) \
-dtb $(dtb)\
-initrd $(initramfs) \
-display none -serial null \
-serial stdio
More peripherals are added than strictly required to fix the panics in
the hopes of avoiding a replication of this problem in the future.
Some of the peripherals which are in the device tree for recent kernels
are implemented in the FPGA fabric. The eMMC/SD mux, which exists as
an unimplemented device is replaced by a wider entry. This updated
entry covers both the mux & the remainder of the FPGA fabric connected
to the MSS using Fabric Interrconnect (FIC) 3.
Link: https://github.com/polarfire-soc/icicle-kit-reference-design#fabric-memory-map
Link: https://ww1.microchip.com/downloads/aemDocuments/documents/FPGA/ProductDocuments/SupportingCollateral/V1_4_Register_Map.zip
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220813135127.2971754-1-mail@conchuod.ie>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Change to generated file ebpf/rss.bpf.skeleton.h backed out]
The current riscv_load_fdt() forces fdt_load_addr to be placed at a dram address within 3GB,
but not all platforms have dram_base within 3GB.
This patch adds an exception for dram base not within 3GB,
which will place fdt at dram_end align 16MB.
riscv_setup_rom_reset_vec() also needs to be modified
Signed-off-by: Dylan Jhong <dylan@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220419115945.37945-1-dylan@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate both AIA IMSIC and AIA APLIC
devices only when "aia=aplic-imsic" parameter is passed along
with machine name in the QEMU command-line. The AIA IMSIC is
only a per-HART MSI controller so we use AIA APLIC in MSI-mode
to forward all wired interrupts as MSIs to the AIA IMSIC.
We also provide "aia-guests=<xyz>" parameter which can be used
to specify number of VS-level AIA IMSIC Guests MMIO pages for
each HART.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-4-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The latest SD card image [1] released by Microchip ships a Linux
kernel with built-in PolarFire SoC I2C driver support. The device
tree file includes the description for the I2C1 node hence kernel
tries to probe the I2C1 device during boot.
It is enough to create an unimplemented device for I2C1 to allow
the kernel to continue booting to the shell.
[1] ftp://ftpsoc.microsemi.com/outgoing/core-image-minimal-dev-icicle-kit-es-sd-20201009141623.rootfs.wic.gz
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-11-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When system memory is larger than 1 GiB (high memory), PolarFire SoC
maps it at address 0x10_0000_0000. Address 0xC000_0000 and above is
aliased to the same 1 GiB low memory with different cache attributes.
At present QEMU maps the system memory contiguously from 0x8000_0000.
This corrects the wrong QEMU logic. Note address 0x14_0000_0000 is
the alias to the high memory, and even physical memory is only 1 GiB,
the HSS codes still tries to probe the high memory alias address.
It seems there is no issue on the real hardware, so we will have to
take that into the consideration in our emulation. Due to this, we
we increase the default system memory size to 1537 MiB (the minimum
required high memory size by HSS) so that user gets notified an error
when less than 1537 MiB is specified.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201101170538.3732-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
