Subscribe to pci_bus_fire_intx_routing_notifier() instead which allows for
having a common piix3_write_config() for the PIIX3 device models.
While at it, move the subscription into machine code to facilitate resolving
TYPE_PIIX3_XEN_DEVICE.
In a possible future followup, pci_bus_fire_intx_routing_notifier() could
be adjusted in such a way that subscribing to it doesn't require
knowledge of the device firing it.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-5-shentey@gmail.com>
Message-Id: <20230403074124.3925-6-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xen_piix3_set_irq() isn't PIIX specific: PIIX is a single PCI device
while xen_piix3_set_irq() maps multiple PCI devices to their respective
IRQs, which is board-specific. Rename xen_piix3_set_irq() to communicate
this.
Also rename XEN_PIIX_NUM_PIRQS to XEN_IOAPIC_NUM_PIRQS since the Xen's
IOAPIC rather than PIIX has this many interrupt routes.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-2-shentey@gmail.com>
Message-Id: <20230403074124.3925-2-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
pci_map_irq_fn's in general seem to be board-specific. So move PIIX3's
pci_slot_get_pirq() to board code to not have PIIX3 make assuptions
about its board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_bus_irqs() coupled together the assignment of pci_set_irq_fn and
pci_map_irq_fn to a PCI bus. This coupling gets in the way when the
pci_map_irq_fn is board-specific while the pci_set_irq_fn is device-
specific.
For example, both of QEMU's PIIX south bridge models have different
pci_map_irq_fn implementations which are board-specific rather than
device-specific. These implementations should therefore reside in board
code. The pci_set_irq_fn's, however, should stay in the device models
because they access memory internal to the model.
Factoring out pci_bus_map_irqs() from pci_bus_irqs() allows the
assignments to be decoupled, resolving the problem described above.
Note also how pci_vpb_realize() which gets touched in this commit
assigns different pci_map_irq_fn's depending on the board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-5-shentey@gmail.com>
[PMD: Factor out in vfu_object_set_bus_irq()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Commit 47a373faa6 (acpi: pc/q35: drop ad-hoc PCI-ISA bridge AML routines and let bus ennumeration generate AML)
moved ISA bridge AML generation to respective devices and was using
aml_alias() to provide PRQx fields in _SB. scope. However, it turned
out that SeaBIOS was not able to process Alias opcode when parsing DSDT,
resulting in lack of keyboard during boot (SeaBIOS console, grub, FreeDOS).
While fix for SeaBIOS is posted
https://mail.coreboot.org/hyperkitty/list/seabios@seabios.org/thread/RGPL7HESH5U5JRLEO6FP77CZVHZK5J65/
fixed SeaBIOS might not make into QEMU-7.2 in time.
Hence this workaround that puts PRQx back into _SB scope
and gets rid of aliases in ISA bridge description, so
DSDT will be parsable by broken SeaBIOS.
That brings back hardcoded references to ISA bridge
PCI0.S08.P40C/PCI0.SF8.PIRQ
where middle part now is auto generated based on slot it's
plugged in, but it should be fine as bridge initialization
also hardcodes PCI address of the bridge so it can't ever
move. Once QEMU tree has fixed SeaBIOS blob, we should be able
to drop this part and revert back to alias based approach
Reported-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221121153613.3972225-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI-ISA bridges that are built in PIIX/Q35 are building its own AML
using AcpiDevAmlIf interface. Now build_append_pci_bus_devices()
gained AcpiDevAmlIf interface support to get AML of devices atached
to PCI slots.
So drop ad-hoc build_q35_isa_bridge()/build_piix4_isa_bridge()
and let PCI bus enumeration to include PCI-ISA bridge AML
when it's enumerated by build_append_pci_bus_devices().
AML change is mostly contextual, which moves whole ISA hierarchy
directly under PCI host bridge instead of it being described
as separate \SB.PCI0.ISA block.
Note:
If bus/slot that hosts ISA bridge has BSEL set, it will gain new
ASUN and _DMS entries (i.e. acpi-index support, but it should not
cause any functional change and that is fine from PCI Firmware
spec point of view), potentially it's possible to suppress that
by adding a flag to PCIDevice but I don't see a reason to do that
yet, I'd rather treat bridge just as any other PCI device if it's
possible.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221017102146.2254096-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
get_system_memory() accesses global state while pci_address_space() uses
whatever has been passed to the device instance, so avoid the global.
Moreover, PIIX4 uses pci_address_space() here as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Rather than registering the reset handler via a function which
appends the handler to a global list, prefer to implement it as
a virtual method - PIIX4 does the same already.
Note that this means that piix3_reset can now also be called writing to
the relevant configuration space register on a PCI bridge.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
xen_piix_pci_write_config_client() is implemented in the xen sub tree and
uses PIIX constants internally, thus creating a direct dependency on
PIIX. Now that xen_set_pci_link_route() is stubbable, the logic of
xen_piix_pci_write_config_client() can be moved to PIIX which resolves
the dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-3-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
PCI interrupt wiring was performed in create() functions which are
obsolete. Move these tasks into QOM functions to modernize the code.
In order to avoid duplicate checking for xen_enabled() the realize
methods are now split.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-10-shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
replaces ad-hoc build_isa_devices_aml() with generic AcpiDevAmlIf
way to build bridge AML including all devices that are attached to
its ISA bus.
Later when PCI is converted to AcpiDevAmlIf, build_piix4_isa_bridge()
will also be dropped since PCI parts itself will take care of
building device prologue/epilogue AML for each enumerated PCI
device.
Expected AML change is contextual, where ISA devices are moved
from separately declared _SB.PCI0.ISA scope , directly under
Device(ISA) node.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-20-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move all the PIIX3 functions to a new file: hw/isa/piix3.c.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
