DeviceClass::reset models a "cold power-on" reset which can
also be used to powercycle a device; but there is no "hot reset"
(a.k.a. soft-reset) method available.
The OMAP MMC Power-Up Control bit is not designed to powercycle
a card, but to disable it without powering it off (pseudo-reset):
Multimedia Card (MMC/SD/SDIO) Interface [SPRU765A]
MMC_CON[11] Power-Up Control (POW)
This bit must be set to 1 before any valid transaction to either
MMC/SD or SPI memory cards.
When 1, the card is considered powered-up and the controller core
is enabled.
When 0, the card is considered powered-down (system dependent),
and the controller core logic is in pseudo-reset state. This is,
the MMC_STAT flags and the FIFO pointers are reset, any access to
MMC_DATA[DATA] has no effect, a write into the MMC.CMD register
is ignored, and a setting of MMC_SPI[STR] to 1 is ignored.
By splitting the 'pseudo-reset' code out of the 'power-on' reset
function, this patch fixes a latent bug in omap_mmc_write(MMC_CON)i
recently exposed by ecd219f7ab.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180706162155.8432-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The load/store API will ease further code movement.
Per the Physical Layer Simplified Spec. "3.6 Bus Protocol":
"In the CMD line the Most Significant Bit (MSB) is transmitted
first, the Least Significant Bit (LSB) is the last."
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since omap_mmc is still using the legacy SD card API, the SD
card created by sd_init() is not plugged into any bus. This
means that the controller has to reset it manually.
Failing to do this mostly didn't affect the guest since the
guest typically does a programmed SD card reset as part of
its SD controller driver initialization, but would mean that
migration fails because it's only in sd_reset() that we
set up the wpgrps_size field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1515506513-31961-5-git-send-email-peter.maydell@linaro.org
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IF_NONE allows read-only, which makes forbidding it in this place
for other types pretty much pointless.
Instead, make sure that all devices for which the check would have
errored out check in their init function that they don't get a read-only
BlockDriverState. This catches even cases where IF_NONE and -device is
used.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
