When the state machine is ready to accept command, the bit 7 of
the status register (SR) is set to 1.
The guest polls the status register and check this bit before
writting command to the internal 'Write State Machine' (WSM).
Set SR.7 bit to 1 when the device is created.
There is no migration impact by this change.
Reference: Read Array Flowchart
"Common Flash Interface (CFI) and Command Sets"
(Intel Application Note 646)
Appendix B "Basic Command Set"
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190715121338.20600-5-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Previous to commit ddb6f2254, the DQ2 bit was incorrectly set
during PROGRAM command (0xA0). The commit reordered the switch
cases to only set the DQ2 bit for the ERASE commands using a
fallthrough, but did not explicit the fallthrough is intentional.
Mark the switch fallthrough with a comment interpretable by C
preprocessors and static analysis tools.
Reported-by: Coverity (CID 1403012)
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20190711130759.27720-1-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This reverts commit 3ae0343db6.
Stephen Checkoway noticed commit 3ae0343db6 is incorrect.
This commit state all parallel flashes are limited to 16-bit
accesses, however the x32 configuration exists in some models,
such the Cypress S29CL032J, which CFI Device Geometry Definition
announces:
CFI ADDR DATA
0x28,0x29 = 0x0003 (x32-only asynchronous interface)
Guests should not be affected by the previous change, because
QEMU does not announce itself as x32 capable:
/* Flash device interface (8 & 16 bits) */
pfl->cfi_table[0x28] = 0x02;
pfl->cfi_table[0x29] = 0x00;
Commit 3ae0343db6 does not restrict the bus to 16-bit accesses,
but restrict the implementation as 16-bit access max, so a guest
32-bit access will result in 2x 16-bit calls.
Now, we have 2 boards that register the flash device in 32-bit
access:
- PPC: taihu_405ep
The CFI id matches the S29AL008J that is a 1MB in x16, while
the code QEMU forces it to be 2MB, and checking Linux it expects
a 4MB flash.
- ARM: Digic4
While the comment says "Samsung K8P3215UQB 64M Bit (4Mx16)",
this flash is 32Mb (2MB). Also note the CFI id does not match
the comment.
To avoid unexpected side effect, we revert commit 3ae0343db6,
and will clean the board code later.
Reported-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
virtio, pc, pci: features, fixes, cleanups
virtio-pmem support.
libvhost user mq support.
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 04 Jul 2019 22:00:49 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
docs: avoid vhost-user-net specifics in multiqueue section
libvhost-user: implement VHOST_USER_PROTOCOL_F_MQ
libvhost-user: support many virtqueues
libvhost-user: add vmsg_set_reply_u64() helper
pc: Move compat_apic_id_mode variable to PCMachineClass
virtio: Don't change "started" flag on virtio_vmstate_change()
virtio: Make sure we get correct state of device on handle_aio_output()
virtio: Set "start_on_kick" on virtio_set_features()
virtio: Set "start_on_kick" for legacy devices
virtio: add "use-started" property
virtio-pci: fix missing device properties
pc: Support for virtio-pmem-pci
numa: Handle virtio-pmem in NUMA stats
hmp: Handle virtio-pmem when printing memory device infos
virtio-pci: Proxy for virtio-pmem
virtio-pmem: sync linux headers
virtio-pci: Allow to specify additional interfaces for the base type
virtio-pmem: add virtio device
pcie: minor cleanups for slot control/status
pcie: work around for racy guest init
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to avoid migration issues, we introduce a "use-started"
property to the base virtio device to indicate whether use
"started" flag or not. This property will be true by default and
set to false when machine type <= 4.0.
Suggested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Message-Id: <20190626023130.31315-2-xieyongji@baidu.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move commands object-add, object-del, qom-get, qom-list,
qom-list-properties, qom-list-types, and qom-set with their types from
misc.json to new qom.json.
Move commands device-list-properties, device_add, device-del, and
event DEVICE_DELETED from misc.json to new qdev.json.
Add both new files to MAINTAINERS section QOM.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrange" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-5-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[Straightforwardly updated for "MAINTAINERS: Make section "QOM" cover
qdev as well"]
During a sector erase (but not a chip erase), the embeded erase program
can be suspended. Once suspended, the sectors not selected for erasure
may be read and programmed. Autoselect mode is allowed during erase
suspend mode. Presumably, CFI queries are similarly allowed so this
commit allows them as well.
Since guest firmware can use status bits DQ7, DQ6, DQ3, and DQ2 to
determine the current state of sector erasure, these bits are properly
implemented.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-10-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
After two unlock cycles and a sector erase command, the AMD flash chips
start a 50 us erase time out. Any additional sector erase commands add a
sector to be erased and restart the 50 us timeout. During the timeout,
status bit DQ3 is cleared. After the time out, DQ3 is asserted during
erasure.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-9-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
When the flash device is performing a chip erase, all commands are
ignored. When it is performing a sector erase, only the erase suspend
command is valid, which is currently not supported.
In particular, the reset command should not cause the device to reset to
read array mode while programming is on going.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-8-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Some flash chips support sectors of different sizes. For example, the
AMD AM29LV160DT has 31 64 kB sectors, one 32 kB sector, two 8 kB
sectors, and a 16 kB sector, in that order. The AM29LV160DB has those in
the reverse order.
The `num-blocks` and `sector-length` properties work exactly as they did
before: a flash device with uniform sector lengths. To get non-uniform
sector lengths for up to four regions, the following properties may be
set
- region 0. `num-blocks0` and `sector-length0`;
- region 1. `num-blocks1` and `sector-length1`;
- region 2. `num-blocks2` and `sector-length2`; and
- region 3. `num-blocks3` and `sector-length3`.
If the uniform and nonuniform properties are set, then both must specify
a flash device with the same total size. It would be better to disallow
both being set, or make `num-blocks0` and `sector-length0` alias
`num-blocks` and `sector-length`, but that would make testing currently
impossible.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased, add assert() on pri_offset]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Manufacturers are allowed to move the PRI table, this is why the
offset is queryable via fixed offsets 0x15/0x16.
Add a variable to hold the offset, so it will be easier to later
move the PRI table.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-17-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The pflash_read()/pflash_write() can check the device endianess
via the pfl->be variable, so remove the 'int be' argument.
Since the big/little MemoryRegionOps are now identical, it is
pointless to declare them both. Unify them.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch to ease review]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Pull out all of the code to modify the status into simple helper
functions. Status handling becomes more complex once multiple
chips are interleaved to produce a single device.
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Xen queue
* Fix build
* xen-block: support feature-large-sector-size
* xen-block: Support IOThread polling for PV shared rings
* Avoid usage of a VLA
* Cleanup Xen headers usage
# gpg: Signature made Mon 24 Jun 2019 16:30:32 BST
# gpg: using RSA key F80C006308E22CFD8A92E7980CF5572FD7FB55AF
# gpg: issuer "anthony.perard@citrix.com"
# gpg: Good signature from "Anthony PERARD <anthony.perard@gmail.com>" [marginal]
# gpg: aka "Anthony PERARD <anthony.perard@citrix.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5379 2F71 024C 600F 778A 7161 D8D5 7199 DF83 42C8
# Subkey fingerprint: F80C 0063 08E2 2CFD 8A92 E798 0CF5 572F D7FB 55AF
* remotes/aperard/tags/pull-xen-20190624:
xen: Import other xen/io/*.h
Revert xen/io/ring.h of "Clean up a few header guard symbols"
xen: Drop includes of xen/hvm/params.h
xen: Avoid VLA
xen-bus / xen-block: add support for event channel polling
xen-bus: allow AioContext to be specified for each event channel
xen-bus: use a separate fd for each event channel
xen-block: support feature-large-sector-size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A Xen public header have been imported into QEMU (by
f65eadb639 "xen: import ring.h from xen"), but there are other header
that depends on ring.h which come from the system when building QEMU.
This patch resolves the issue of having headers from the system
importing a different copie of ring.h.
This patch is prompt by the build issue described in the previous
patch: 'Revert xen/io/ring.h of "Clean up a few header guard symbols"'
ring.h and the new imported headers are moved to
"include/hw/xen/interface" as those describe interfaces with a guest.
The imported headers are cleaned up a bit while importing them: some
part of the file that QEMU doesn't use are removed (description
of how to make hypercall in grant_table.h have been removed).
Other cleanup:
- xen-mapcache.c and xen-legacy-backend.c don't need grant_table.h.
- xenfb.c doesn't need event_channel.h.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190621105441.3025-3-anthony.perard@citrix.com>
This patch introduces a poll callback for event channel fd-s and uses
this to invoke the channel callback function.
To properly support polling, it is necessary for the event channel callback
function to return a boolean saying whether it has done any useful work or
not. Thus xen_block_dataplane_event() is modified to directly invoke
xen_block_handle_requests() and the latter only returns true if it actually
processes any requests. This also means that the call to qemu_bh_schedule()
is moved into xen_block_complete_aio(), which is more intuitive since the
only reason for doing a deferred poll of the shared ring should be because
there were previously insufficient resources to fully complete a previous
poll.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-4-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
A recent Xen commit [1] clarified the semantics of sector based quantities
used in the blkif protocol such that it is now safe to create a xen-block
device with a logical_block_size != 512, as long as the device only
connects to a frontend advertizing 'feature-large-block-size'.
This patch modifies xen-block accordingly. It also uses a stack variable
for the BlockBackend in xen_block_realize() to avoid repeated dereferencing
of the BlockConf pointer, and changes the parameters of
xen_block_dataplane_create() so that the BlockBackend pointer and sector
size are passed expicitly rather than implicitly via the BlockConf.
These modifications have been tested against a recent Windows PV XENVBD
driver [2] using a xen-disk device with a 4kB logical block size.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commit;h=67e1c050e36b2c9900cca83618e56189effbad98
[2] https://winpvdrvbuild.xenproject.org:8080/job/XENVBD-master/126
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190409164038.25484-1-paul.durrant@citrix.com>
[Edited error message]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The uninitialized memory allocated for the command FIFO of the
floppy controller during the VM hardware initialization incurs
many unwanted reports by Valgrind when VM state is being saved.
That verbosity hardens a search for the real memory issues when
the iotests run. Particularly, the patch eliminates 20 unnecessary
reports of the Valgrind tool in the iotest #169.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-id: 1559154027-282547-1-git-send-email-andrey.shinkevich@virtuozzo.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
This adds a new parameter to blk_new() which requires its callers to
declare from which AioContext this BlockBackend is going to be used (or
the locks of which AioContext need to be taken anyway).
The given context is only stored and kept up to date when changing
AioContexts. Actually applying the stored AioContext to the root node
is saved for another commit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an Error parameter to blk_set_aio_context() and use
bdrv_child_try_set_aio_context() internally to check whether all
involved nodes can actually support the AioContext switch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since we now support the message VHOST_USER_GET_INFLIGHT_FD
and VHOST_USER_SET_INFLIGHT_FD. The backend is able to restart
safely because it can track inflight I/O in shared memory.
This patch allows qemu to reconnect the backend after
connection closed.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Ni Xun <nixun@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190320112646.3712-7-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
`nvme_dma_read_prp` erronously used `qemu_iovec_*to*_buf` instead of
`qemu_iovec_*from*_buf` when the request involved the controller memory
buffer.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Reviewed-by: Kenneth Heitke <kenneth.heitke@intel.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
