Currently, we set PostcopyState blindly to RUNNING, even we found the
previous state is not LISTENING. This will lead to a corner case.
First let's look at the code flow:
qemu_loadvm_state_main()
ret = loadvm_process_command()
loadvm_postcopy_handle_run()
return -1;
if (ret < 0) {
if (postcopy_state_get() == POSTCOPY_INCOMING_RUNNING)
...
}
>From above snippet, the corner case is loadvm_postcopy_handle_run()
always sets state to RUNNING. And then it checks the previous state. If
the previous state is not LISTENING, it will return -1. But at this
moment, PostcopyState is already been set to RUNNING.
Then ret is checked in qemu_loadvm_state_main(), when it is -1
PostcopyState is checked. Current logic would pause postcopy and retry
if PostcopyState is RUNNING. This is not what we expect, because
postcopy is not active yet.
This patch makes sure state is set to RUNNING only previous state is
LISTENING by checking the state first.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested by: Peter Xu <peterx@redhat.com>
Message-Id: <20191010011316.31363-3-richardw.yang@linux.intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
There are two places to call function postcopy_ram_incoming_cleanup()
postcopy_ram_listen_thread on migration success
loadvm_postcopy_handle_listen one setup failure
On success, the vm will never accept another migration. On failure,
PostcopyState is transited from LISTENING to END and would be checked in
qemu_loadvm_state_main(). If PostcopyState is RUNNING, migration would
be paused and retried.
Currently PostcopyState is set to END in function
postcopy_ram_incoming_cleanup(). With above analysis, we can take this
step out and postpone this till the end of listen thread to indicate the
listen thread is done.
This is a preparation patch for later cleanup.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191006000249.29926-3-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixed up in merge to the 1 parameter postcopy_state_set
If mis->have_listen_thread is true, this means current PostcopyState
must be LISTENING or RUNNING. While the check at the beginning of the
function makes sure the state transaction happens when its previous
PostcopyState is ADVISE or DISCARD.
This means we would never touch this check.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191006000249.29926-2-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
During migration, there are several places to iterate on
savevm.handlers. And on each iteration, we need to check its ops and
related callbacks before invoke it.
Generally, ops is the first element to check, and it is only necessary
to check it once.
This patch clean all the related part in savevm.c to check ops only once
in those iterations.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190819032804.8579-1-richardw.yang@linux.intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Header cleanup patches for 2019-08-13
# gpg: Signature made Fri 16 Aug 2019 12:39:12 BST
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-include-2019-08-13-v2: (29 commits)
sysemu: Split sysemu/runstate.h off sysemu/sysemu.h
sysemu: Move the VMChangeStateEntry typedef to qemu/typedefs.h
Include sysemu/sysemu.h a lot less
Clean up inclusion of sysemu/sysemu.h
numa: Move remaining NUMA declarations from sysemu.h to numa.h
Include sysemu/hostmem.h less
numa: Don't include hw/boards.h into sysemu/numa.h
Include hw/boards.h a bit less
Include hw/qdev-properties.h less
Include qemu/main-loop.h less
Include qemu/queue.h slightly less
Include hw/hw.h exactly where needed
Include qom/object.h slightly less
Include exec/memory.h slightly less
Include migration/vmstate.h less
migration: Move the VMStateDescription typedef to typedefs.h
Clean up inclusion of exec/cpu-common.h
Include hw/irq.h a lot less
typedefs: Separate incomplete types and function types
ide: Include hw/ide/internal a bit less outside hw/ide/
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This patch fix a multifd migration bug in migration speed calculation, this
problem can be reproduced as follows:
1. start a vm and give a heavy memory write stress to prevent the vm be
successfully migrated to destination
2. begin a migration with multifd
3. migrate for a long time [actually, this can be measured by transferred bytes]
4. migrate cancel
5. begin a new migration with multifd, the migration will directly run into
migration_completion phase
Reason as follows:
Migration update bandwidth and s->threshold_size in function
migration_update_counters after BUFFER_DELAY time:
current_bytes = migration_total_bytes(s);
transferred = current_bytes - s->iteration_initial_bytes;
time_spent = current_time - s->iteration_start_time;
bandwidth = (double)transferred / time_spent;
s->threshold_size = bandwidth * s->parameters.downtime_limit;
In multifd migration, migration_total_bytes function return
qemu_ftell(s->to_dst_file) + ram_counters.multifd_bytes.
s->iteration_initial_bytes will be initialized to 0 at every new migration,
but ram_counters is a global variable, and history migration data will be
accumulated. So if the ram_counters.multifd_bytes is big enough, it may lead
pending_size >= s->threshold_size become false in migration_iteration_run
after the first migration_update_counters.
Signed-off-by: Ivan Ren <ivanren@tencent.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <1564741121-1840-1-git-send-email-ivanren@tencent.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
LOADVM_QUIT allows a command to quit all layers of nested loadvm loops,
while current return value check is not that proper even it works now.
Current return value check "ret & LOADVM_QUIT" would return true if
bit[0] is 1. This would be true when ret is -1 which is used to indicate
an error of handling a command.
Since there is only one place return LOADVM_QUIT and no other
combination of return value, use "ret == LOADVM_QUIT" would be more
proper.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190718064257.29218-1-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Currently, there is no information about error if outgoing migration was failed
because of file channel errors.
Example (QMP session):
-> { "execute": "migrate", "arguments": { "uri": "exec:head -c 1" }}
<- { "return": {} }
...
-> { "execute": "query-migrate" }
<- { "return": { "status": "failed" }} // There is not error's description
And even in the QEMU's output there is nothing.
This patch
1) Adds errp for the most of QEMUFileOps
2) Adds qemu_file_get_error_obj/qemu_file_set_error_obj
3) And finally using of qemu_file_get_error_obj in migration.c
And now, the status for the mentioned fail will be:
-> { "execute": "query-migrate" }
<- { "return": { "status": "failed",
"error-desc": "Unable to write to command: Broken pipe" }}
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Message-Id: <20190422103420.15686-1-yury-kotov@yandex-team.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
On source side, we have qemu_savevm_state_header() to send related data,
while on the receiving side those steps are scattered in
qemu_loadvm_state().
This patch wrap those related steps into qemu_loadvm_state_header() to
make it friendly to read.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190424004700.12766-5-richardw.yang@linux.intel.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This reverts commit 3df663e575.
This reverts commit b605c47b57.
Command line option --only-migratable is for disallowing any
configuration that can block migration.
Initially, --only-migratable set global variable @only_migratable.
Commit 3df663e575 "migration: move only_migratable to MigrationState"
replaced it by MigrationState member @only_migratable. That was a
mistake.
First, it doesn't make sense on the design level. MigrationState
captures the state of an individual migration, but --only-migratable
isn't a property of an individual migration, it's a restriction on
QEMU configuration. With fault tolerance, we could have several
migrations at once. --only-migratable would certainly protect all of
them. Storing it in MigrationState feels inappropriate.
Second, it contributes to a dependency cycle that manifests itself as
a bug now.
Putting @only_migratable into MigrationState means its available only
after migration_object_init().
We can't set it before migration_object_init(), so we delay setting it
with a global property (this is fixup commit b605c47b57 "migration:
fix handling for --only-migratable").
We can't get it before migration_object_init(), so anything that uses
it can only run afterwards.
Since migrate_add_blocker() needs to obey --only-migratable, any code
adding migration blockers can run only afterwards. This contributes
to the following dependency cycle:
* configure_blockdev() must run before machine_set_property()
so machine properties can refer to block backends
* machine_set_property() before configure_accelerator()
so machine properties like kvm-irqchip get applied
* configure_accelerator() before migration_object_init()
so that Xen's accelerator compat properties get applied.
* migration_object_init() before configure_blockdev()
so configure_blockdev() can add migration blockers
The cycle was closed when recent commit cda4aa9a5a "Create block
backends before setting machine properties" added the first
dependency, and satisfied it by violating the last one. Broke block
backends that add migration blockers.
Moving @only_migratable into MigrationState was a mistake. Revert it.
This doesn't quite break the "migration_object_init() before
configure_blockdev() dependency, since migrate_add_blocker() still has
another dependency on migration_object_init(). To be addressed the
next commit.
Note that the reverted commit made -only-migratable sugar for -global
migration.only-migratable=on below the hood. Documentation has only
ever mentioned -only-migratable. This commit removes the arcane &
undocumented alternative to -only-migratable again. Nobody should be
using it.
Conflicts:
include/migration/misc.h
migration/migration.c
migration/migration.h
vl.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190401090827.20793-3-armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Currently we don't check which capabilities set in the source QEMU.
We just expect that the target QEMU has the same enabled capabilities.
Add explicit validation for capabilities to make sure that the target VM
has them too. This is enabled for only new capabilities to keep compatibily.
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Message-Id: <20190215174548.2630-6-yury-kotov@yandex-team.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Manual merge
Switch the announcements to using the new announce timer.
Move the code that does it to announce.c rather than savevm
because it really has nothing to do with the actual migration.
Migration starts the announce from bh's and so they're all
in the main thread/bql, and so there's never any racing with
the timers themselves.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
There is really no difference between live migration and savevm, except
that savevm does not require bdrv_invalidate_cache to be implemented
by all disks. However, it is unlikely that savevm is used with anything
except qcow2 disks, so the penalty is small and worth the improvement
in catching bad usage of savevm.
Only one place was taking care of savevm when adding a migration blocker,
and it can be removed.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During an active background migration, snapshot will trigger a
segmentfault. As snapshot clears the "current_migration" struct
and updates "to_dst_file" before it finds out that there is a
migration task, Migration accesses the null pointer in
"current_migration" struct and qemu crashes eventually.
Signed-off-by: Jia Lina <jialina01@baidu.com>
Signed-off-by: Chai Wen <chaiwen@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20181026083620.10172-1-jialina01@baidu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Error reporting patches for 2018-10-22
# gpg: Signature made Mon 22 Oct 2018 13:20:23 BST
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-error-2018-10-22: (40 commits)
error: Drop bogus "use error_setg() instead" admonitions
vpc: Fail open on bad header checksum
block: Clean up bdrv_img_create()'s error reporting
vl: Simplify call of parse_name()
vl: Fix exit status for -drive format=help
blockdev: Convert drive_new() to Error
vl: Assert drive_new() does not fail in default_drive()
fsdev: Clean up error reporting in qemu_fsdev_add()
spice: Clean up error reporting in add_channel()
tpm: Clean up error reporting in tpm_init_tpmdev()
numa: Clean up error reporting in parse_numa()
vnc: Clean up error reporting in vnc_init_func()
ui: Convert vnc_display_init(), init_keyboard_layout() to Error
ui/keymaps: Fix handling of erroneous include files
vl: Clean up error reporting in device_init_func()
vl: Clean up error reporting in parse_fw_cfg()
vl: Clean up error reporting in mon_init_func()
vl: Clean up error reporting in machine_set_property()
vl: Clean up error reporting in chardev_init_func()
qom: Clean up error reporting in user_creatable_add_opts_foreach()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Calling error_report() in a function that takes an Error ** argument
is suspicious. save_snapshot() and load_snapshot() do that, and then
fail without setting an error. Wrong. The HMP commands survive this
unscathed, since hmp_handle_error() does nothing when no error has
been set. Callers main() (on behalf of -loadvm) and
replay_vmstate_init() crash, but I'm not sure the error is possible
there.
Screwed up when commit 377b21ccea (v2.12.0) added incorrect error
handling right next to correct examples. Fix by calling error_setg()
instead of error_report().
Fixes: 377b21ccea
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181017082702.5581-13-armbru@redhat.com>
There are several stages during loadvm/savevm process. In different stage,
migration incoming processes different types of sections.
We want to control these stages more accuracy, it will benefit COLO
performance, we don't have to save type of QEMU_VM_SECTION_START
sections everytime while do checkpoint, besides, we want to separate
the process of saving/loading memory and devices state.
So we add three new helper functions: qemu_load_device_state() and
qemu_savevm_live_state() to achieve different process during migration.
Besides, we make qemu_loadvm_state_main() and qemu_save_device_state()
public, and simplify the codes of qemu_save_device_state() by calling the
wrapper qemu_savevm_state_header().
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Zhang Chen <zhangckid@gmail.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We should not load PVM's state directly into SVM, because there maybe some
errors happen when SVM is receving data, which will break SVM.
We need to ensure receving all data before load the state into SVM. We use
an extra memory to cache these data (PVM's ram). The ram cache in secondary side
is initially the same as SVM/PVM's memory. And in the process of checkpoint,
we cache the dirty pages of PVM into this ram cache firstly, so this ram cache
always the same as PVM's memory at every checkpoint, then we flush this cached ram
to SVM after we receive all PVM's state.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Zhang Chen <zhangckid@gmail.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We need to know if migration is going into COLO state for
incoming side before start normal migration.
Instead by using the VMStateDescription to send colo_state
from source side to destination side, we use MIG_CMD_ENABLE_COLO
to indicate whether COLO is enabled or not.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Zhang Chen <zhangckid@gmail.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
There's a couple of error paths in qemu_loadvm_state
which happen early on but after we've initialised the
load state; that needs to be cleaned up otherwise
we can hit asserts if the state gets reinitialised later.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20180914170430.54271-3-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This patch adds a small hint for the failure case of the load snapshot
process. It may be useful for users to remember that the VM
configuration has changed between the save and load processes.
(qemu) loadvm vm-20180903083641
Unknown savevm section or instance 'cpu_common' 4.
Make sure that your current VM setup matches your saved VM setup, including any hotplugged devices
Error -22 while loading VM state
(qemu) device_add host-spapr-cpu-core,core-id=4
(qemu) loadvm vm-20180903083641
(qemu) c
(qemu) info status
VM status: running
It also exits Qemu if the snapshot cannot be loaded before reaching the
main loop (-loadvm in the command line).
$ qemu-system-ppc64 ... -loadvm vm-20180903083641
qemu-system-ppc64: Unknown savevm section or instance 'cpu_common' 4.
Make sure that your current VM setup matches your saved VM setup, including any hotplugged devices
qemu-system-ppc64: Error -22 while loading VM state
$
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.ibm.com>
Message-Id: <20180903162613.15877-1-joserz@linux.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This patch implements bi-directional RDMA QIOChannel. Because different
threads may access RDMAQIOChannel currently, this patch use RCU to protect it.
Signed-off-by: Lidong Chen <lidongchen@tencent.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We were checking against -EIO, assuming that it will cover all IO
failures. But actually it is not. One example is that in
qemu_loadvm_section_start_full() we can have tons of places that will
return -EINVAL even if the error is caused by IO failures on the
network.
Let's loosen the recovery check logic here to cover all the error cases
happened by removing the explicit check against -EIO. After all we
won't lose anything here if any other failure happened.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180710091902.28780-3-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
