Rule R_CQRV says that if two pending interrupts have the same
group priority then ties are broken by looking at the subpriority.
We had a comment describing this but had forgotten to actually
implement the subpriority comparison. Correct the omission.
(The further tie break rules of "lowest exception number" and
"secure before non-secure" are handled implicitly by the order
in which we iterate through the exceptions in the loops.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-2-peter.maydell@linaro.org
The Raspberry Pi boards have a physical memory map which does
not allow for more than 1GB of RAM. Currently if the user tries
to ask for more then we fail in a confusing way:
$ qemu-system-aarch64 --machine raspi3 -m 8G
Unexpected error in visit_type_uintN() at qapi/qapi-visit-core.c:164:
qemu-system-aarch64: Parameter 'vcram-base' expects uint32_t
Aborted (core dumped)
Catch this earlier and diagnose it with a more friendly message:
$ qemu-system-aarch64 --machine raspi3 -m 8G
qemu-system-aarch64: Requested ram size is too large for this machine: maximum is 1GB
Fixes: https://bugs.launchpad.net/qemu/+bug/1794187
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
The ARM virt machines put firmware in flash memory. To configure it,
you use -drive if=pflash,unit=0,... and optionally -drive
if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, we get two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
We recently solved this problem for x86 PC machines, in commit
ebc29e1bea. See the commit message for design rationale.
This commit solves it for ARM virt basically the same way: new machine
properties pflash0, pflash1 forward to the onboard flash devices'
properties. Requires creating the onboard devices in the
.instance_init() method virt_instance_init(). The existing code to
pick up drives defined with -drive if=pflash is replaced by code to
desugar into the machine properties.
There are a few behavioral differences, though:
* The flash devices are always present (x86: only present if
configured)
* Flash base addresses and sizes are fixed (x86: sizes depend on
images, mapped back to back below a fixed address)
* -bios configures contents of first pflash (x86: -bios configures ROM
contents)
* -bios is rejected when first pflash is also configured with -machine
pflash0=... (x86: bios is silently ignored then)
* -machine pflash1=... does not require -machine pflash0=... (x86: it
does).
The actual code is a bit simpler than for x86 mostly due to the first
two differences.
Before the patch, all the action is in create_flash(), called from the
machine's .init() method machvirt_init():
main()
machine_run_board_init()
machvirt_init()
create_flash()
create_one_flash() for flash[0]
create
configure
includes obeying -drive if=pflash,unit=0
realize
map
fall back to -bios
create_one_flash() for flash[1]
create
configure
includes obeying -drive if=pflash,unit=1
realize
map
update FDT
To make the machine properties work, we need to move device creation
to its .instance_init() method virt_instance_init().
Another complication is machvirt_init()'s computation of
@firmware_loaded: it predicts what create_flash() will do. Instead of
predicting what create_flash()'s replacement virt_firmware_init() will
do, I decided to have virt_firmware_init() return what it did.
Requires calling it a bit earlier.
Resulting call tree:
main()
current_machine = object_new()
...
virt_instance_init()
virt_flash_create()
virt_flash_create1() for flash[0]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash0 as alias for drive [NEW]
virt_flash_create1() for flash[1]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash1 as alias for drive [NEW]
for all machine props from the command line: machine_set_property()
...
property_set_alias() for machine props pflash0, pflash1
...
set_drive() for cfi.pflash01 prop drive
this is how -machine pflash0=... etc set
machine_run_board_init(current_machine);
virt_firmware_init()
pflash_cfi01_legacy_drive()
legacy -drive if=pflash,unit=0 and =1 [NEW]
virt_flash_map()
virt_flash_map1() for flash[0]
configure: num-blocks
realize
map
virt_flash_map1() for flash[1]
configure: num-blocks
realize
map
fall back to -bios
virt_flash_fdt()
update FDT
You have László to thank for making me explain this in detail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20190416091348.26075-4-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The loop does two things: map legacy -drive to properties, and collect
all the backends for use after the loop. The next patch will factor
out the former for reuse in hw/arm/virt.c. To make that easier,
rearrange the loop so it does the first thing first, and the second
thing second.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190416091348.26075-2-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix the check preventing calling pixman functions that would access
memory outside allocated vram. The r128 X driver sometimes seem to try
blits that span outside vram, this check prevents crashing QEMU in
that case. (The r128 X driver may have problems even on real hardware
so I'm not sure if it's a client bug or emulation problem but at least
QEMU should survive.)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Message-Id: <20190409110732.5C5FF7465DB@zero.eik.bme.hu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The SPICE_RING_PROD_ITEM() macro is initializing a local
'uint64_t *' variable to point to the 'el' field inside
the QXLReleaseRing struct. This uint64_t field is not
guaranteed aligned as the struct is packed.
Code should not take the address of fields within a
packed struct. Changing the SPICE_RING_PROD_ITEM()
macro to avoid taking the address of the field is
impractical. It is clearer to just remove the macro
and inline its functionality in the three call sites
that need it.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190412121626.19829-6-berrange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The documentation URL is not working, but is backed up by the
Wayback Machine on the Internet Archive.
Replace the outdated link by a captured one.
Add another link to the VGADOC4b.ZIP archive content.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190504121650.12651-1-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb: bugfixes for mtp and xhci, split ohci-pci.
# gpg: Signature made Fri 03 May 2019 07:59:39 BST
# gpg: using RSA key 4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>" [full]
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>" [full]
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>" [full]
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/kraxel/tags/usb-20190503-v2-pull-request:
hw/usb: avoid format truncation warning when formatting port name
hw/usb/hcd-ohci: Move PCI-related code into a separate file
hw/usb/hcd-ohci: Do not use PCI functions with sysbus devices in ohci_die()
usb/xhci: avoid trigger assertion if guest write wrong epid
usb-mtp: change default to success for usb_mtp_update_object
usb-mtp: fix alignment of access of ObjectInfo filename field
usb-mtp: fix string length for filename when writing metadata
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/usb/hcd-xhci.c: In function ‘usb_xhci_realize’:
hw/usb/hcd-xhci.c:3339:66: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 5 [-Wformat-trunca\
tion=]
3339 | snprintf(port->name, sizeof(port->name), "usb2 port #%d", i+1);
| ^~
hw/usb/hcd-xhci.c:3339:54: note: directive argument in the range [1, 2147483647]
3339 | snprintf(port->name, sizeof(port->name), "usb2 port #%d", i+1);
| ^~~~~~~~~~~~~~~
The xhci code formats the port name into a fixed length
buffer which is only large enough to hold port numbers
upto 5 digits in decimal representation. We're never
going to have a port number that large, so aserting the
port number is sensible is sufficient to tell GCC the
formatted string won't be truncated.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190412121626.19829-5-berrange@redhat.com>
[ kraxel: also s/int/unsigned int/ to tell gcc they can't
go negative. ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Both functions, object_initialize() and object_property_add_child() increase
the reference counter of the new object, so one of the references has to be
dropped afterwards to get the reference counting right. Otherwise the child
object might not be properly cleaned up when the parent gets destroyed.
Some functions of the pci-host devices miss to drop one of the references.
Fix it by using object_initialize_child() instead, which takes care of
calling object_initialize(), object_property_add_child() and object_unref()
in the right order.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190430191552.4027-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some machines (like the pxa2xx-based ARM machines) only have a sysbus
OHCI controller, but no PCI. With the new Kconfig-style build system,
it will soon be possible to create QEMU binaries that only contain
such PCI-less machines. However, the two OHCI controllers, for sysbus
and for PCI, are currently both located in one file, so the PCI code
is still required for linking here. Move the OHCI-PCI device code
into a separate file, so that it is possible to use the sysbus OHCI
device also without the PCI dependency.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190419075625.24251-3-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The ohci_die() function always assumes to be running with a PCI OHCI
controller and calls the PCI-specific functions pci_set_word(). However,
this function might also get called for the sysbus OHCI devices, so it
likely fails in that case. To fix this issue, change the code now, so that
there are two implementations now, one for sysbus and one for PCI, and
use the right function via a function pointer in the OHCIState structure.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190419075625.24251-2-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
we found the following core in our environment:
0 0x00007fc6b06c2237 in raise ()
1 0x00007fc6b06c3928 in abort ()
2 0x00007fc6b06bb056 in __assert_fail_base ()
3 0x00007fc6b06bb102 in __assert_fail ()
4 0x0000000000702e36 in xhci_kick_ep (...)
5 0x000000000047897a in memory_region_write_accessor (...)
6 0x000000000047767f in access_with_adjusted_size (...)
7 0x000000000047944d in memory_region_dispatch_write (...)
(mr=mr@entry=0x7fc6a0138df0, addr=addr@entry=156, data=1648892416,
size=size@entry=4, attrs=attrs@entry=...)
8 0x000000000042df17 in address_space_write_continue (...)
10 0x000000000043084d in address_space_rw (...)
11 0x000000000047451b in kvm_cpu_exec (cpu=cpu@entry=0x1ab11b0)
12 0x000000000045dcf5 in qemu_kvm_cpu_thread_fn (arg=0x1ab11b0)
13 0x0000000000870631 in qemu_thread_start (args=args@entry=0x1acfb50)
14 0x00000000008959a7 in thread_entry_for_hotfix (pthread_cb=<optimized out>)
15 0x00007fc6b0a60dd5 in start_thread ()
16 0x00007fc6b078a59d in clone ()
(gdb) f 5
5 0x000000000047897a in memory_region_write_accessor (...)
529 mr->ops->write(mr->opaque, addr, tmp, size);
(gdb) p /x tmp
$9 = 0x62481a00 <-- last byte 0x00 is @epid
xhci_doorbell_write() already check the upper bound of @slotid an @epid,
it also need to check the lower bound.
Cc: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Longpeng <longpeng2@huawei.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 1556605301-44112-1-git-send-email-longpeng2@huawei.com
[ kraxel: fixed typo in subject line ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit c5ead51f90 (usb-mtp: return incomplete transfer on a lstat
failure) checks if lstat succeeded when updating attributes of a
file. However, it also changed behavior to return an error by
default. This is incorrect because for smaller file sizes, Qemu
will attempt to write the file in one go and there won't be
an object for it.
Fixes: c5ead51f90
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: jpgwojv9pwv.fsf@linux.bootlegged.copy
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The ObjectInfo struct's "filename" field is following a uint8_t
field in a packed struct and thus has bad alignment for a 16-bit
field. Switch the field to to uint8_t and use the helper function
for accessing unaligned 16-bit data.
Note that although the MTP spec specifies big endian, when transported
over the USB protocol, data is little endian.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20190415154503.6758-4-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The ObjectInfo 'length' field provides the length of the
wide character string filename. This is then converted to
a multi-byte character string. This may have a different
byte count to the wide character string. We should use the
C string length of the multi-byte string instead.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20190415154503.6758-2-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In the v7M architecture, if an exception is generated in the process
of doing the lazy stacking of FP registers, the handling of
possible escalation to HardFault is treated differently to the normal
approach: it works based on the saved information about exception
readiness that was stored in the FPCCR when the stack frame was
created. Provide a new function armv7m_nvic_set_pending_lazyfp()
which pends exceptions during lazy stacking, and implements
this logic.
This corresponds to the pseudocode TakePreserveFPException().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-22-peter.maydell@linaro.org
Implement the code which updates the FPCCR register on an
exception entry where we are going to use lazy FP stacking.
We have to defer to the NVIC to determine whether the
various exceptions are currently ready or not.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190416125744.27770-12-peter.maydell@linaro.org
The M-profile floating point support has three associated config
registers: FPCAR, FPCCR and FPDSCR. It also makes the registers
CPACR and NSACR have behaviour other than reads-as-zero.
Add support for all of these as simple reads-as-written registers.
We will hook up actual functionality later.
The main complexity here is handling the FPCCR register, which
has a mix of banked and unbanked bits.
Note that we don't share storage with the A-profile
cpu->cp15.nsacr and cpu->cp15.cpacr_el1, though the behaviour
is quite similar, for two reasons:
* the M profile CPACR is banked between security states
* it preserves the invariant that M profile uses no state
inside the cp15 substruct
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-4-peter.maydell@linaro.org
The SMMUNotifierNode struct is not necessary and brings extra
complexity so let's remove it. We now directly track the SMMUDevices
which have registered IOMMU MR notifiers.
This is inspired from the same transformation on intel-iommu
done in commit b4a4ba0d68
("intel-iommu: remove IntelIOMMUNotifierNode")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20190409160219.19026-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support for a generic MMU-less Nios II board that can
be used e.g. for bare-metal compiler testing with the linker script
and startup code provided by libgloss. Nios II booting is also
tweaked so that bare-metal binaries start executing in RAM starting at
0x00000000, rather than an alias at 0xc0000000, which allows features
such as unwinding to work when binaries are linked to start at the
beginning of the address space.
The generic_nommu.c parts are based on code by Andrew Jenner, which was
in turn based on code by Marek Vasut.
Originally by Marek Vasut and Andrew Jenner.
Signed-off-by: Sandra Loosemore <sandra@codesourcery.com>
Signed-off-by: Julian Brown <julian@codesourcery.com>
Signed-off-by: Andrew Jenner <andrew@codesourcery.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1554321185-2825-2-git-send-email-sandra@codesourcery.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ppc patch queue 2019-04-26
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
# gpg: Signature made Fri 26 Apr 2019 07:02:19 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190426: (36 commits)
target/ppc: improve performance of large BAT invalidations
ppc/hash32: Rework R and C bit updates
ppc/hash64: Rework R and C bit updates
ppc/spapr: Use proper HPTE accessors for H_READ
target/ppc: Don't check UPRT in radix mode when in HV real mode
target/ppc/kvm: Convert DPRINTF to traces
target/ppc/trace-events: Fix trivial typo
spapr: Drop duplicate PCI swizzle code
spapr_pci: Get rid of duplicate code for node name creation
target/ppc: Style fixes for translate/spe-impl.inc.c
target/ppc: Style fixes for translate/vmx-impl.inc.c
target/ppc: Style fixes for translate/vsx-impl.inc.c
target/ppc: Style fixes for translate/fp-impl.inc.c
target/ppc: Style fixes for translate.c
target/ppc: Style fixes for translate_init.inc.c
target/ppc: Style fixes for monitor.c
target/ppc: Style fixes for mmu_helper.c
target/ppc: Style fixes for mmu-hash64.[ch]
target/ppc: Style fixes for mmu-hash32.[ch]
target/ppc: Style fixes for misc_helper.c
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
x86 queue, 2019-04-25
* Hygon Dhyana CPU model (Pu Wen)
* Categorize a few devices in hw/i386 (Ernest Esene)
* Support host-cache-info on TOPOEXT CPUID leaf (Stanislav Lanci)
# gpg: Signature made Thu 25 Apr 2019 19:12:25 BST
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-next-pull-request:
Pass through cache information for TOPOEXT CPUs
Categorize devices: iommu
Categorize devices: IGD passthrough ISA bridge
i386: Add new Hygon 'Dhyana' CPU model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With MT-TCG, we are now running translation in a racy way, thus
we need to mimic hardware when it comes to updating the R and
C bits, by doing byte stores.
The current "store_hpte" abstraction is ill suited for this, we
replace it with two separate callbacks for setting R and C.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190411080004.8690-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
