The VIA south bridges are able to relocate and toggle (enable or disable) their
SuperI/O functions. So far this is hardcoded such that all functions are always
enabled and are located at fixed addresses.
Some PC BIOSes seem to probe for I/O occupancy before activating such a function
and issue an error in case of a conflict. Since the functions are currently
enabled on reset, conflicts are always detected. Prevent that by implementing
relocation and toggling of the SuperI/O functions.
Note that all SuperI/O functions are now deactivated upon reset (except for
VT82C686B's serial ports where Fuloong 2e's rescue-yl seems to expect them to be
enabled by default). Rely on firmware to configure the functions accordingly.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-12-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The chip has 4 pins (called PIRQA-D in VT82C686B and PINTA-D in
VT8231) that are meant to be connected to PCI IRQ lines and allow
routing PCI interrupts to the ISA PIC. Route these in
via_isa_set_irq() to make it possible to share them with internal
functions that can also be routed to the same ISA IRQs.
Fixes: 2fdadd02e6
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <8c4513d8b78fac40e6d4e65a0a4b3a7f2f278a4b.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The VIA integrated south bridge chips combine several functions and
allow routing their interrupts to any of the ISA IRQs also allowing
multiple sources to share the same ISA IRQ. E.g. pegasos2 firmware
configures everything to use IRQ 9 but amigaone routes them to
separate ISA IRQs so the current simplified routing does not work.
Bring back via_isa_set_irq() and change it to take the component that
wants to change an IRQ and keep track of interrupt status of each
source separately and do the mapping to ISA IRQ within the ISA bridge.
This may not handle cases when an ISA IRQ is controlled by devices
directly, not going through via_isa_set_irq() such as serial, parallel
or keyboard but these IRQs being conventionally fixed are not likely
to be change by guests or share with other devices so this does not
cause a problem in practice.
This reverts commit 4e5a20b6da.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <1c3902d4166234bef0a476026441eaac3dd6cda5.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to implement it as well. The real chip may allow routing IRQs from
internal functions independently of PCI interrupts but since guests
usually configute it to a single shared interrupt we don't model that
here for simplicity.
Note: The implementation was taken from piix4_set_irq() in hw/isa/piix4.
Suggested-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <fbb016c7d0e19093335c237e15f5f6c62c4393b4.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ realized (properties are consumed).
Some devices (objects) might depend on other devices. When creating
the 'QOM composition tree', parent objects can't be 'realized' until
all their children are. We might also have circular dependencies.
A common circular dependency occurs with IRQs. Device (A) has an
output IRQ wired to device (B), and device (B) has one to device (A).
When (A) is realized and connects its IRQ to an unrealized (B), the
IRQ handler on (B) is not yet created. QEMU pass IRQ between objects
as pointer. When (A) poll (B)'s IRQ, it is NULL. Later (B) is realized
and its IRQ pointers are populated, but (A) keeps a reference to a
NULL pointer.
A common pattern to bypass this circular limitation is to use 'proxy'
objects. Proxy (P) is created (and realized) before (A) and (B). Then
(A) and (B) can be created in different order, it doesn't matter: (P)
pointers are already populated.
Commit bb98e0f59c ("hw/isa/vt82c686: Remove intermediate IRQ
forwarder") neglected the QOM/QDev circular dependency issue, and
removed the 'proxy' between the southbridge, its PCI functions and the
interrupt controller, resulting in PCI functions wiring output IRQs to
'NULL', leading to guest failures (IRQ never delivered) [1] [2].
Since we are entering feature freeze, it is safer to revert the
offending patch until we figure a way to strengthen our APIs.
[1] https://lore.kernel.org/qemu-devel/928a8552-ab62-9e6c-a492-d6453e338b9d@redhat.com/
[2] https://lore.kernel.org/qemu-devel/cover.1677628524.git.balaton@eik.bme.hu/
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <cdfb3c5a42e505450f6803124f27856434c5b298.1677628524.git.balaton@eik.bme.hu>
[PMD: Reworded description]
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
RTCState only represents a Motorola MC146818 model,
not any RTC chipset. Rename the structure as MC146818RtcState
using:
$ sed -i -e s/RTCState/MC146818RtcState/g $(git grep -wl RTCState)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210233116.80311-2-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
isa_bus_irqs() register an array of input IRQs on
the ISA bus. Rename it as isa_bus_register_input_irqs().
Mechanical change using:
$ sed -i -e 's/isa_bus_irqs/isa_bus_register_input_irqs/g' \
$(git grep -wl isa_bus_irqs)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-10-philmd@linaro.org>
Directly dispatch ISA IRQs to 'cpu_intr' output IRQ
by removing the intermediate via_isa_request_i8259_irq()
handler. Rename ISA IRQs array as 'isa_irqs_in' to
emphasize these are input IRQs.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-5-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
According to good QOM practice, an object should only deal with objects
of its own sub tree. Having devices create an alias on the machine
object doesn't respect this good practice. To resolve this, create the
alias in the machine's code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-14-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The IDE function is closely tied to the ISA function (e.g. the IDE
interrupt routing happens there), so it makes sense that the IDE
function is instantiated within the south bridge itself.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The object creation now happens in chip-specific init methods which
allows the realize methods to be consolidated into one method. Shifting
the logic into the init methods has the addidional advantage that the
parent object's init methods are called implicitly - like constructors
in object-oriented languages.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220901114127.53914-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
ppc patch queue 2021-05-04
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
# gpg: Signature made Tue 04 May 2021 06:52:39 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210504: (46 commits)
hw/ppc/pnv_psi: Use device_cold_reset() instead of device_legacy_reset()
hw/ppc/spapr_vio: Reset TCE table object with device_cold_reset()
hw/intc/spapr_xive: Use device_cold_reset() instead of device_legacy_reset()
target/ppc: removed VSCR from SPR registration
target/ppc: Reduce the size of ppc_spr_t
target/ppc: Clean up _spr_register et al
target/ppc: Add POWER10 exception model
target/ppc: rework AIL logic in interrupt delivery
target/ppc: move opcode table logic to translate.c
target/ppc: code motion from translate_init.c.inc to gdbstub.c
spapr_drc.c: handle hotunplug errors in drc_unisolate_logical()
spapr.h: increase FDT_MAX_SIZE
spapr.c: do not use MachineClass::max_cpus to limit CPUs
ppc: Rename current DAWR macros and variables
target/ppc: POWER10 supports scv
target/ppc: Fix POWER9 radix guest HV interrupt AIL behaviour
docs/system: ppc: Add documentation for ppce500 machine
roms/u-boot: Bump ppce500 u-boot to v2021.04 to fix broken pci support
roms/Makefile: Update ppce500 u-boot build directory name
ppc/spapr: Add support for implement support for H_SCM_HEALTH
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The VT8231 south bridge is very similar to VT82C686B but there are
some differences in register addresses and functionality, e.g. the
VT8231 only has one serial port. This commit adds VT8231_SUPERIO
subclass based on the abstract VIA_SUPERIO class to emulate the
superio part of VT8231.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <8108809321f9ecf3fb1aea22ddaeccc7c3a57c8e.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If SMM is not supported, ACPI fixed hardware doesn't support
legacy-mode. ACPI-only platform. Where SCI_EN in PM1_CNT register is
always set.
The bit tells OS legacy mode(SCI_EN cleared) or ACPI mode(SCI_EN set).
With the next patch (setting fadt.smi_cmd = 0 when smm isn't enabled),
guest Linux tries to switch to ACPI mode, finds smi_cmd = 0, and then
fails to initialize acpi subsystem. This patch proactively fixes it.
This patch changes guest ABI. To keep compatibility, use
"smm-compat" introduced by earlier patch. If the property is true,
disable new behavior.
ACPI spec 4.8.10.1 PM1 Event Grouping
PM1 Eanble Registers
> For ACPI-only platforms (where SCI_EN is always set)
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <500f62081626997e46f96377393d3662211763a8.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the ISA devices that are part of the VIA south bridge,
superio chip are wired up by board code. Move creation of these ISA
devices to the VIA ISA bridge model so that board code does not need
to access ISA bus. This also allows vt82c686b-superio to be made
internal to vt82c686 which allows implementing its configuration via
registers in subseqent commits.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <bf9400cc8e4ddd3129aa5678de4d3cf38384805f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The vt82c686b-pm model can be shared between VT82C686B and VT8231. The
only difference between the two is the device id in what we emulate so
make an abstract via-pm model by renaming appropriately and add types
for vt82c686b-pm and vt8231-pm based on it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <34969fc7be984fa070479bfb9f748993a0aef31b.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Similar to the SMBus io registers there is a power management io range
that is set via similar base address reg and enable bit. Some handling
of this was already there but with several problems: using the wrong
registers and bits, wrong size range, not acually updating mapping and
handling reset correctly, nor emulating any of the actual io
registers. Some of these errors are fixed up here.
After this patch we use the correct base address register, enable bit
and region size and allow guests to map/unmap this region, but we
still don't emulate any of the registers in this range.
PMD notes regarding the Configuration Space Power Management Registers:
- 0x40 General Configuration 0
- 0x41 General Configuration 1
. Bit 7: I/O Enable for ACPI I/O Base
- 0x48 Power Mgmt I/O Base
. Bit 0: Always set
. Bits 7-15: Power Management I/O Register Base Address
(this explains the change 0xffc0 -> 0xff80)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 4/4, added notes]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
