This patch adds minimal support for AXP-221 PMU and connect it to
bananapi M2U board.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
During SPL boot several DRAM Controller registers are used. Most
important registers are those related to DRAM initialization and
calibration, where SPL initiates process and waits until certain bit is
set/cleared.
This patch adds these registers, initializes reset values from user's
guide and updates state of registers as SPL expects it.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-3-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
Add PCI interface support for PVPANIC device. Create a new file pvpanic-pci.c
where the PCI specific routines reside and update the build system with the new
files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To ease the PCI device addition in next patches, split the code as follows:
- generic code (read/write/setup) is being kept in pvpanic.c
- ISA dependent code moved to pvpanic-isa.c
Also, rename:
- ISA_PVPANIC_DEVICE -> PVPANIC_ISA_DEVICE.
- TYPE_PVPANIC -> TYPE_PVPANIC_ISA.
- MemoryRegion io -> mr.
- pvpanic_ioport_* in pvpanic_*.
Update the build system with the new files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PolarFire SoC DDR Memory Controller mainly includes 2 modules,
called SGMII PHY module and the CFG module, as documented in the
chipset datasheet.
This creates a single file that groups these 2 modules, providing
the minimum functionalities that make the HSS DDR initialization
codes happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-3-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 8 LEDs connected to the MCC.
This replaces the 'mps2_scc_leds' trace events by the generic
'led_set_intensity' event.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-7-f4bug@amsat.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 2 LEDs connected to the FPGA.
This replaces the 'mps2_fpgaio_leds' trace events by the generic
'led_set_intensity' event.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-6-f4bug@amsat.org>
Add a LED device which can be connected to a GPIO output.
They can also be dimmed with PWM devices. For now we do
not implement the dimmed mode, but in preparation of a
future implementation, we start using the LED intensity.
LEDs are limited to a fixed set of colors.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-2-f4bug@amsat.org>
Inside the 680x0 Macintosh, VIA (Versatile Interface Adapter) is used
to interface the keyboard, Mouse, and real-time clock. It also provides
control line for the floppy disk driver, video interface, sound circuitry
and serial interface.
This implementation is based on the MOS6522 object.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-6-laurent@vivier.eu>
The device is only used by some few boards. Let's use a proper Kconfig
switch so that we only compile this code if we really need it.
Message-Id: <20190817101931.28386-8-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the fsl-imx31 / kzm machine.
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
For devices that require msi_init/msix_init to succeed, add a
dependency on CONFIG_MSI_NONBROKEN. This will prevent those devices
from appearing in a binary that cannot instantiate them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
