NXP PCF8574 and compatible ICs are simple I2C GPIO expanders.
PCF8574 incorporates quasi-bidirectional IO, and simple
communication protocol, when IO read is I2C byte read, and
IO write is I2C byte write. User can think of it as
open-drain port, when line high state is input and line low
state is output.
Signed-off-by: Dmitrii Sharikhin <d.sharikhin@yadro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <f1552d822276e878d84c01eba2cf2c7c9ebdde00.camel@yadro.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externally" (using input
irqs) results in an out irq (transmitted to SYSCFG)
- output mode : setting a bit in ODR sets the corresponding out irq
(if this line is configured in output mode)
- pull-up, pull-down
- push-pull, open-drain
Difference with the real GPIOs :
- Alternate Function and Analog mode aren't implemented :
pins in AF/Analog behave like pins in input mode
- floating pins stay at their last value
- register IDR reset values differ from the real one :
values are coherent with the other registers reset values
and the fact that AF/Analog modes aren't implemented
- setting I/O output speed isn't supported
- locking port bits isn't supported
- ADC function isn't supported
- GPIOH has 16 pins instead of 2 pins
- writing to registers LCKR, AFRL, AFRH and ASCR is ineffective
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240305210444.310665-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The gpio array is declared as a dense array:
qemu_irq gpios[ASPEED_GPIO_NR_PINS];
(AST2500 has 228, AST2400 has 216, AST2600 has 208)
However, this array is used like a matrix of GPIO sets
(e.g. gpio[NR_SETS][NR_PINS_PER_SET] = gpio[8][32])
size_t offset = set * GPIOS_PER_SET + gpio;
qemu_set_irq(s->gpios[offset], !!(new & mask));
This can result in an out-of-bounds access to "s->gpios" because the
gpio sets do _not_ have the same length. Some of the groups (e.g.
GPIOAB) only have 4 pins. 228 != 8 * 32 == 256.
To fix this, I converted the gpio array from dense to sparse, to that
match both the hardware layout and this existing indexing code.
Fixes: 4b7f956862 ("hw/gpio: Add basic Aspeed GPIO model for AST2400 and AST2500")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211008033501.934729-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
NRF51_GPIO_REG_CNF_END doesn't actually refer to the start of the last
valid CNF register: it's referring to the last byte of the last valid
CNF register.
This hasn't been a problem up to now, as current implementation in
memory.c turns an unaligned 4-byte read from 0x77f to a single byte read
and the qtest only looks at the least-significant byte of the register.
But when running with patches which fix unaligned accesses in memory.c,
the qtest breaks.
Considering NRF51 doesn't support unaligned accesses, the simplest fix
is to actually set NRF51_GPIO_REG_CNF_END to the start of the last valid
CNF register: 0x77c.
Now, qtests work with or without the unaligned access patches.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cameron Esfahani <dirty@apple.com>
Message-id: 51b427f06838622da783d38ba56e3630d6d85c60.1586925392.git.dirty@apple.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GPIO pins are arranged in groups of 8 pins labeled A,B,..,Y,Z,AA,AB,AC.
(Note that the ast2400 controller only goes up to group AB).
A set has four groups (except set AC which only has one) and is
referred to by the groups it is composed of (eg ABCD,EFGH,...,YZAAAB).
Each set is accessed and controlled by a bank of 14 registers.
These registers operate on a per pin level where each bit in the register
corresponds to a pin, except for the command source registers. The command
source registers operate on a per group level where bits 24, 16, 8 and 0
correspond to each group in the set.
eg. registers for set ABCD:
|D7...D0|C7...C0|B7...B0|A7...A0| <- GPIOs
|31...24|23...16|15....8|7.....0| <- bit position
Note that there are a couple of groups that only have 4 pins.
There are two ways that this model deviates from the behaviour of the
actual controller:
(1) The only control source driving the GPIO pins in the model is the ARM
model (as there currently aren't models for the LPC or Coprocessor).
(2) None of the registers in the model are reset tolerant (needs
integration with the watchdog).
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-2-clg@kaod.org
[clg: fixed missing header files
made use of HWADDR_PRIx to fix compilation on windows ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
